posi

Started by art.flame, January 28, 2012, 02:42:17 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages1
User actions

art.flame

January 28, 2012, 02:42:17 PM
Hi all,
I bought a ford 8" posi  third member ,should i use a special oil?
who can help me with an exploded view

thx Art

jaybee

#1
January 28, 2012, 04:47:31 PM
There are both special lubricants and additives for conventional gear oil to be used in these units. Either approach is highly recommended, though I'm not sure what brands might be available in Europe.
Rudeness is the weak man's imitation of strength. Eric Hoffer  (1902 - 1983)

Crosley.In.AZ

#2
January 28, 2012, 05:02:58 PM
I've used various gear oils from dyno oils to synthetic oils  that were listed for posi type differentials.. these oils all allowed the diff to  chatter on my 8 inch Ford posi till I added Ford CM-19546-A1  additive
Tony

 Plutophobia (Fear of money)

tomslik

#3
January 28, 2012, 05:25:24 PM
that's the ONLY stuff we use at the shop.
ford posi additive seems to be the best
The last thing I want to do is hurt you. But it\'s still on my list

art.flame

#4
January 29, 2012, 06:26:33 AM
thx for the info, i'll see if i can find it overhere

@ tomslik, if i can't find it overhere can i order it from you?

Art

enjenjo

#5
January 30, 2012, 11:13:17 AM
I am not finding anything on the net with a blow up of the Posi unit. It's pretty simple.
Welcome to hell. Here's your accordion.

wayne petty

#6
January 30, 2012, 05:38:57 PM
some blow up diagrams...

http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/27/a2/e0/large/0900c1528027a2e0.gif


a better diagram of the limited slip....

http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/27/a2/d3/large/0900c1528027a2d3.gif


tools needed for removing and installing pressed on axles bearings..

http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/27/a2/e9/large/0900c1528027a2e9.gif

after looking at that.. man am i glad somebody came up with bearing splitters...

http://www.harborfreight.com/large-bearing-separator-3979.html

http://www.harborfreight.com/14-piece-gear-puller-set-30305.html

http://www.harborfreight.com/bearing-separator-and-puller-set-93980.html


and these are real time savers..

if you have to remove the axle bearings on C clip axles...

http://www.harborfreight.com/rear-axle-bearing-puller-set-66380.html

some stores have them in the loan a tool section..

last thing..   aluminum tapered roller bearing cup drivers...

http://www.harborfreight.com/10-piece-bearing-race-and-seal-driver-set-95853.html

more than any of you wanted to know... but since you all live so far.. all i can share is knowledge..  and LINKs...



####################################

and a HUGE TIP...

if your rear end is chattering around corners...

make SLOW circles to the left  as tight as you can .. then more to the right.. this works the lube in between the clutch packs...

slow so you don't just spin it out..   this works it in.. and smoothes any burrs...

please.. invest in some super magnets..  position it into the housing so they attract the metal filings out of the oil.. keep it out of the bearings..

i had never seen the posi lube device that fits inside the ford housing so any gear oil off the top of the case is deposited into the posi case openings..

art.flame

#8
January 31, 2012, 11:31:28 AM
speachless, thx wayne

:oops: me and google
Print
Go Up Pages1
User actions