Vance - C cab ideas

Started by sirstude, May 26, 2007, 08:21:50 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

sirstude

Vance,

Dennis had his C cab out this weekend, so here are a couple of pictures.  Just click on them.

Doug





1965 Impala SS  502
1941 Olds


Watcher of #974 1953 Studebaker Bonneville pas record holder B/BGCC 249.945 MPH.  He sure is FAST

www.theicebreaker.us

EMSjunkie

COOL :!:  :!:

Thanks Doug. 8)

reckon I could get some frame dimensions on that little beaut :?:
I'm about ready to start building the frame.

Vance
"I don\'t know what your problem is, but I bet its hard to pronounce"

1934 Ford 3 Window
Member, Rural Rodders
Member, National Sarcasm Society  "Like we need your support"
*****Co-Founder  Team Smart*****

sirstude

I will get some from him.  He has built many 'T' frames.

Doug
1965 Impala SS  502
1941 Olds


Watcher of #974 1953 Studebaker Bonneville pas record holder B/BGCC 249.945 MPH.  He sure is FAST

www.theicebreaker.us

EMSjunkie

Quote from: "sirstude"I will get some from him.  He has built many 'T' frames.

Doug

Wonderful  :D  :D   Thanks Doug 8)

I'll prolly be asking ALOT of questions :shock:  

decided to build my own frame. my Nephew can get me a pretty good deal on tubing and stuff, so why not :wink:

wish me luck :-o

Vance
"I don\'t know what your problem is, but I bet its hard to pronounce"

1934 Ford 3 Window
Member, Rural Rodders
Member, National Sarcasm Society  "Like we need your support"
*****Co-Founder  Team Smart*****

Dave

Vance i built the frame for my first car a 27 t bucket. keep in mind you can do it anyway you want. I did about a 6 inch rear kick and used 2x4 tubing with about a 3/16 wall . I even used that tubing for the front of the frame but if i had to do it over again id use round tubing in the front for better eye candy. I built it on a cement floor with ni jig and it was straight. It just takes time.get a motor and tranny and set em along with the body on the floor and grab your tape measure :!:
Dave :arrow:  :wink:  :arrow:

GPster

Quote from: "jusjunk"It just takes time.get a motor and tranny and set em along with the body on the floor and grab your tape measure :!:
Dave :arrow:  :wink:  :arrow:
I'd have to agree. Any frame will be a "one-off" depending on the pieces you decide to use. If you gathered the pieces then you would be building mounts and brackets rather than building adapters. You could even build something out of wood that layed on the axels and held the cab up. You could have like Enjenjo's tech contest and get suggestions from everybody. Decide on wheel and tire sizes that you'd like. Worn out tires should be easy to come up with and their heigth and width wouldn't be that far for new. GPster

EMSjunkie

Thanks for the input guys, I really appreciate it :D

this will be my first attempt at building a frame :shock:

but, I have the will, want-to, and the way :lol:

keep the idears comin' 8)

Vance
"I don\'t know what your problem is, but I bet its hard to pronounce"

1934 Ford 3 Window
Member, Rural Rodders
Member, National Sarcasm Society  "Like we need your support"
*****Co-Founder  Team Smart*****

Rayvyn

***SFC-Team Smart***
____________________

What can a bird do that a man can\'t?

Whistle through his pecker...

EMSjunkie

Quote from: "Rayvyn"Hey Dude, check it out. You could keep your ewe in the baaaaaaaack and no one would ever know...
http://cgi.ebay.com/ebaymotors/1923-FORD-C-CAB_W0QQitemZ330125854610QQihZ014QQcategoryZ7251QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

That thing is about butt-ugly :shock:

no self-respecting ewe would be caught dead in that :lol:  :lol:


Vance
"I don\'t know what your problem is, but I bet its hard to pronounce"

1934 Ford 3 Window
Member, Rural Rodders
Member, National Sarcasm Society  "Like we need your support"
*****Co-Founder  Team Smart*****