Has anyone used the large view welding helmet ? Let me know what you thank
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
Rodder's Roundtable / 50 Olds vin location
November 28, 2010, 08:43:47 PM
Would anyone know the location's of the vin # the one on the door cassing is missing. I have paper work to compare.
#3
Rodder's Roundtable / Petronix HEI Dist
February 25, 2010, 07:38:45 PM
Vac advance to the dist should you use the timed vac or the manfold vac.
#4
Rodder's Roundtable / Net safety Sw C6 Trans
October 13, 2009, 12:37:27 PM
Wayne thanks ..
http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/07/c2/b2/medium/0900c1528007c2b2.gif
ADJUSTMENT
Loosen the two switch adjusting screws.
Place the transmission lever in N .
Rotate the switch and insert a No. 43 drill bit, shank end into the gauge pin holes of the switch.
The drill bit must be inserted about 1 / 2 in. (12.7mm) into the three holes.
Tighten the attaching bolts and remove the drill bit.
waynes comment...
see the wire holder on the right side of the switch... without that holder.. the wires going to the switch will break... they have also been known to short together .. so when the key is turned on... the engine starts cranking.. ...[/quote]
http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/07/c2/b2/medium/0900c1528007c2b2.gif
ADJUSTMENT
Loosen the two switch adjusting screws.
Place the transmission lever in N .
Rotate the switch and insert a No. 43 drill bit, shank end into the gauge pin holes of the switch.
The drill bit must be inserted about 1 / 2 in. (12.7mm) into the three holes.
Tighten the attaching bolts and remove the drill bit.
waynes comment...
see the wire holder on the right side of the switch... without that holder.. the wires going to the switch will break... they have also been known to short together .. so when the key is turned on... the engine starts cranking.. ...[/quote]
#5
Rodder's Roundtable / Net safety Sw C6 Trans
October 11, 2009, 10:39:10 PM
[Waynne I have the correct sw in hand need to know how to align it up with the shift linkage and the sw lever on the trans. SW1148
#6
Rodder's Roundtable / Net safety Sw C6 Trans
October 11, 2009, 07:58:38 PM
Can anyone tell me how to install a net/backup switch on a c6 trans my trans didn't have one to go by.
#7
Rodder's Roundtable / Steering Colum wire code
March 31, 2009, 01:38:42 AM
Wayne looks like that will do it Thanks to you & crdnblu
#8
Rodder's Roundtable / Steering Colum wire code
March 30, 2009, 08:58:50 PM
No one screw holds the switch in place, and the wheel has to be removed
#9
Rodder's Roundtable / Steering Colum wire code
March 30, 2009, 08:17:37 PM
Would any one know the wire color code for a 79 Ford (Cougar) Steering Colum or where I can get it.
#10
Rodder's Roundtable / 50 OLDS
September 15, 2008, 12:08:48 AM
Can any one give me an idea as to the worth of a 50 Olds Coupe 100% there and only surface rust with damage to one front fender that is repairable I has been setting in storage (under cover). I have no interest in it but she has asked me to find it's worth.
Pages1