Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Daveyboy

#1
Rodder's Roundtable / 9" gear ratio question
January 03, 2009, 11:31:27 AM
"Anyway, mileage on that trip usually shows 11-12 mpg with the 3.70's and the one trip wth the 3.00's showed 13 mpg. "

WOW i have a sbc 330 hp vortex heads New from chevy 370 gears. And i get 16 in town and 21 on the road with a 700 r4 trans
But at 70 i am running about 2800.
Would 300 gears give me more mpg?
#2
Rodder's Roundtable / 9" gear ratio question
January 02, 2009, 08:44:58 PM
Ok C9 why did you make the change?
Did you get better mileage?
#3
Rodder's Roundtable / Chat tonight
December 28, 2008, 08:56:19 PM
OHHH boy do we have pic of it?
hehehe
#4
Rodder's Roundtable / Need a favor
November 05, 2008, 07:38:01 PM
Done baby done
Good luck
Dave
#5
Rodder's Roundtable / coupe update
July 29, 2008, 08:11:40 AM
Yes heated seats.
Bad back so i need them. but i hid all the stuff.
Dave
#6
Rodder's Roundtable / coupe update
July 28, 2008, 10:52:16 PM
Thanks you all helped out on the build.
THANKS again
Dave
#7
Rodder's Roundtable / coupe update
July 28, 2008, 09:13:34 PM
Well it has been a bit so here is where i am at as of now.
I still have 3 A/C line by the eng to clean up (did not like the 1st ones)
And finush installing the heated seats and Ipod stuff but that will come in time.
Here you all go
#8
Rodder's Roundtable / seat belts placement???????
June 27, 2008, 10:17:12 PM
Glide says just mount the belts to the seat frame.
With 3/8 grade 8 bolts and i am good.
Sound right to you?
#9
Rodder's Roundtable / seat belts placement???????
June 26, 2008, 11:22:25 PM
Ok it is time to put seat belts in the coupe.  I have a glide seat.
Some have told me to bolt the belts to the seat frame ?
or should i bolt it in the steel of the body? The frame is bolted to the steel in the body now the frame is big but i am just asking?
#10
Rodder's Roundtable / Can I sit in here? - Intro
June 18, 2008, 02:21:11 PM
Good to have you here!!
You will like this place noone tell you what you should like and not like. They just help out  :D  :P
#11
Rodder's Roundtable / S W speedo prob
June 15, 2008, 08:44:57 AM
Well this is where i am at as of now.  
We put a 10k resistor in on the feed line from the trans and that fixed the bouncing when not moving. But the speedo is so far off i cant calibrate it. They say my trans is putting out 200k pulse per mile and the speedo can only handle 16k  
So i had to buy a box from Dakota digital to split the pulses down.  
The car is at the upostrey shop so i cant try it now
sorry for the bad spelling but i cant think its 5 am and i am going to bed now
#12
Rodder's Roundtable / CHAT?
June 11, 2008, 08:17:24 PM
WE DOING IT?
#13
Rodder's Roundtable / S W speedo prob
June 02, 2008, 10:36:27 PM
yellow is now on the frame
And when the purple wire was off it did the same thing
#14
Rodder's Roundtable / S W speedo prob
June 02, 2008, 10:19:55 PM
ok i ran a NEW wire from the purple wire at the trans sender to the speedo and i have the same prob.
Now what?
#15
Ok i think there is a trans man or to here.
I need a 2nd trans pick up for a 700r4 to test with
I will pay ofr it if one of you can tell me what you have is for a 700r4
Thanks Dave