I will try that on monday night Thanks
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#17
Rodder's Roundtable / S W speedo prob
June 02, 2008, 12:28:11 AM
It does not go up and down with eng speed just goes all over from 20 to 160
#18
Rodder's Roundtable / S W speedo prob
June 01, 2008, 11:41:54 PM
I did call them and they told me to put the 1k restior in.
The speedo runs and runs with eng running and NOT moving
I will call them again and see
The speedo runs and runs with eng running and NOT moving
I will call them again and see
#19
Rodder's Roundtable / S W speedo prob
June 01, 2008, 06:55:56 PM
I have a S W winged speedo and a 700r4 trans elec pic up and speedo is elec.
Here is the prob.
If i start the car the speedo will go from 20 to 140 and all around and click off the miles.
I have put a 1k restistor in on the ground and then to the frame to ground (from the yellow wire at the trans pick up to the frame)
What is going on?
And how do i fix it?
Here is the prob.
If i start the car the speedo will go from 20 to 140 and all around and click off the miles.
I have put a 1k restistor in on the ground and then to the frame to ground (from the yellow wire at the trans pick up to the frame)
What is going on?
And how do i fix it?
#20
Rodder's Roundtable / Remember the day...
May 26, 2008, 09:29:03 AM
Amen!! May God Bless you one and ALL.
#21
Rodder's Roundtable / frame tilt?? HELP trying to fix today
May 26, 2008, 12:41:53 AM
no all welding was done by the time i got it as a roller
and yes lower on driver side
and yes lower on driver side
#22
Rodder's Roundtable / frame tilt?? HELP trying to fix today
May 25, 2008, 11:47:22 PM
it was built by Squeak Bell so i dont think that is it?
#23
Rodder's Roundtable / frame tilt?? HELP trying to fix today
May 25, 2008, 11:03:09 PM
well i changed the mono spring from left to right and it still leans?
What the heck??!!!
What the heck??!!!
#24
Rodder's Roundtable / frame tilt?? HELP trying to fix today
May 25, 2008, 09:16:59 PM
I will check the shackles.
But the car sits low front and back if that help anyone
But the car sits low front and back if that help anyone
#25
Rodder's Roundtable / frame tilt?? HELP trying to fix today
May 25, 2008, 01:34:22 PM
Ok i have a 1/2" tilt on the driver side of my coupe.
I have hair pins. When i measure from the mono spring to the frame, the driver side has 1 3/4 inch and the passenger side has 1 1/4 inch.
Queston is can the hair pins adj make this happen?
Dave
I have hair pins. When i measure from the mono spring to the frame, the driver side has 1 3/4 inch and the passenger side has 1 1/4 inch.
Queston is can the hair pins adj make this happen?
Dave
#26
Rodder's Roundtable / It's alive ALIVE!!!
May 18, 2008, 09:30:18 PM
Well after a long day of elec work with friends Mike and Frank. It's Alive
here are some pic of the 1st ride no dash in but all the elec is run. so on monday i will hook up and the gauges
SMILING DAVE
here are some pic of the 1st ride no dash in but all the elec is run. so on monday i will hook up and the gauges
SMILING DAVE
#27
Rodder's Roundtable / 32 3window linc plate placemnt
May 15, 2008, 07:15:55 PM
Can you show me a close up?
And where did you get that part?
thanks Dave
And where did you get that part?
thanks Dave
#28
Rodder's Roundtable / 32 3window linc plate placemnt
May 15, 2008, 04:37:06 PM
I have the stock tank and bar there. I want to put a hollywood light on but there is not much room.
Any one have a pic of that?
Any one have a pic of that?
#29
Rodder's Roundtable / 32 3window linc plate placemnt
May 15, 2008, 12:57:13 AM
Ok I know some of you have built a 32 3window high boy
show me how you mounted you linc. plate.
The back pan is so much smaller on a 3 window than a 5
Show me guy
show me how you mounted you linc. plate.
The back pan is so much smaller on a 3 window than a 5
Show me guy
#30
Rodder's Roundtable / work i did this week end
May 11, 2008, 06:52:49 PM
Well i got the body back on friday. And am getting to do the elec next Sat.
So here is what i got done!
Still more work to do but it looks like a car now lol
So here is what i got done!
Still more work to do but it looks like a car now lol